Log:
Downloads : 1   Arquivo Tamanho: 3 mb   Fabricante : Husqvarna  
Categoria : Clippers
@name@name

This will speed oil consumption, and require more frequent oil tank refills. 6. To adjust oil pump to max, the control screw must be pressed in slightly prior to turning. Failure to do so could damage the pump or screw. WARNING DANGER THE OIL FLOW RATE ADJUSTING SCREW HAS 3 INCREMENTAL SETTINGS. 7. Wipe debris from around the oil fill cap prior to re-filling the oil reservoir. WARNING DANGER NEVER FILL THE OIL TANK OR ADJUST THE OIL FLOW WHILE MOTOR IS RUNNING. DISCONNECT POWER CORD FROM THE POW

Downloads : 1   Arquivo Tamanho: 3 mb   Fabricante : Husqvarna  
Categoria : Clippers
@name

Severe injuries can result if you try to use this machine with only one hand or with an insecure grip. 28. Thoroughly inspect the area where equipment is to be used and removed all objects, which can be thrown by the machine. 29. Always keep area clear of children, pets, and bystanders. 30. Always inspect your unit before each use and ensure that all handles, guards and fasteners are secure, operating, and in place. Be sure that all electrical cords are not damaged or broken. 31. Always maintain

Downloads : 0   Arquivo Tamanho: 2 mb   Fabricante : Husqvarna  
Categoria : Clippers
@name

KEEP A FIRM GRIP WITH BOTH HANDS WHILE BLADES ARE MOVING AND/OR MOTOR IS RUNNING. KEEP A SURE FOOTING. DO NOT OVERREACH. IF YOUR TRIMMER BECOMES JAMMED, RELEASE SWITCH AND STOP MOTOR. MAKE SURE BLADES HAVE STOPPED COMPLETELY. UNPLUG THE UNIT, THEN REMOVE THE OBSTRUCTION. WARNING – DANGER SWITCH OFF THE MOTOR AND UNPLUG THE UNIT BEFORE LUBRICATING OR ADJUSTING THE BLADES. 1.To adjust the blade angle, first shut off the motor. Next, grip the blade adjustment handle. Then move the quick release lev

Downloads : 3   Arquivo Tamanho: 556 kb   Fabricante : Husqvarna  
Categoria : Clippers
@name

2. Remove carriage bolts, taking care to support handlebar. 3. Set handlebar to desired height. 4. Line up holes in upper handlebar with holes in lower handlebar. Be sure to use the same holes on each side. 5. Reinstall carriage bolts and wing knobs. Tighten securely. OX0080 GB - 12 CUTTING HEIGHT ADJUSTMENT CUTTING HEIGHT ADJUSTMENT NOTE: There must always be at least one spacer between the cutter disk and the height guide. 1. Hex Shaft 2. Spacers 3. Cutter Disk 4. Height Guide 5. Washer 6. Loc

Downloads : 1   Arquivo Tamanho: 700 kb   Fabricante : Husqvarna  
Categoria : Clippers

Downloads : 0   Arquivo Tamanho: 700 kb   Fabricante : Husqvarna  
Categoria : Clippers

Downloads : 5   Arquivo Tamanho: 700 kb   Fabricante : Husqvarna  
Categoria : Clippers

Downloads : 2   Arquivo Tamanho: 700 kb   Fabricante : Husqvarna  
Categoria : Clippers

Downloads : 2   Arquivo Tamanho: 700 kb   Fabricante : Husqvarna  
Categoria : Clippers

Downloads : 20   Arquivo Tamanho: 2 mb   Fabricante : Husqvarna  
Categoria : Clippers
@name

• Align the hole in the throttle handle for the fixing screw with the hole on the handlebars. • Refit the screw in the rear of the throttle handle. • Fit the screw through the throttle handle and the handlebars and tighten. • Unscrew the handle from the handlebar bracket. • Position the handlebars as shown. Fit the bracket components and tighten the handle lightly. • Put on the harness and hang the machine in the suspension hook. Now finely adjust so that the machine gives a comfortable working





categorias