Log:
Downloads : 1   Arquivo Tamanho: 17 mb   Fabricante : Philips  
Categoria : Fans
@name@name

Important safeguardsREAD ALL INSTRUCTIONS BEFORE USING YOUR PHILIPS AVENT SINGLE ELECTRONIC BREAST PUMPWhen using electrical products, especially when children

Downloads : 0   Arquivo Tamanho: 14 mb   Fabricante : Philips  
Categoria : Fans
@name

Important safeguardsREAD ALL INSTRUCTIONS BEFORE USING YOUR PHILIPS AVENT TWIN ELECTRONIC BREAST PUMPWhen using electrical products, especially when children

Downloads : 0   Arquivo Tamanho: 13 mb   Fabricante : Hunter Fan  
Categoria : Fans
@name@name@name

If you have questions, contact the manufacturer at the phone number or address listed in the warranty. 2. Before installing, servicing, or cleaning the unit, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers in the off position, securely attach a prominent warning device, such as a tag, to the service panel. 3. Installation work and electrical wiring must be done by qualified person(s) in accord

Downloads : 7   Arquivo Tamanho: 13 mb   Fabricante : Hunter Fan  
Categoria : Fans
@name@name@name

7. Install fan at least 5 feet (1.52 m) above the floor. 8. Never place a switch where it can be reached from a tub or shower. 9. This unit must be grounded. E F G H I J M N O x4 * * * NOTE:Strain relief cable connector must be installed. Not Included. A B C 95044-01-096 95029-01-000 77481-01-000 03242-01-232 95491-06-000 74508-03-133 97258-01-000 65219-01-000 77521-01-000 75184-01-092 97260-01-000 P 76079-02-481 x2 D Extra Screws K L 3/8” Cable Connector 3 1 Turn off the power source. Tools Nee

Downloads : 0   Arquivo Tamanho: 11 mb   Fabricante : Hunter Fan  
Categoria : Fans
@name@name@name

If ducting does not fit securely, an adapter may need to be purchased. Install the wiring cover plate. Make sure all wiring connections are inside the box or under the wiring cover plate. 42950-01 04/18/2007 6 A19J A20 0000IA18 0000A17 ONOFFA21 A22E1Go to stepon page 17 to attach grille. Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. Connect wiring harness. DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRI

Downloads : 0   Arquivo Tamanho: 11 mb   Fabricante : CDA  
Categoria : Fans
@name@name@name

Accumulated deposits of grease are a fire hazard. • This appliance must not be used over cook tops powered by wood or coal or in any case, over cook tops with power levels that could damage the appliance. Never use steam or high-pressure devices for cleaning your hood (regulations regarding electrical safety). • Never use the hood without the grease filters. • The minimum distance between the open down draft and the surface above it needs to be 400 mm. • When moving the down draft, never pl

Downloads : 0   Arquivo Tamanho: 11 mb   Fabricante : Philips  
Categoria : Fans
@name@name@name@name@name@name@name@name@name@name@name@name

58 portuguêS do BraSilimportanteLeia atentamente este manual do usuário antes de usar o extrator de leite e guarde-o para consultas futuras.perigo - Mantenha o

Downloads : 0   Arquivo Tamanho: 11 mb   Fabricante : Philips  
Categoria : Fans

Downloads : 0   Arquivo Tamanho: 10 mb   Fabricante : CDA  
Categoria : Fans
@name@name@name

After it has reached a height of 180 mm from the cooketop, press OFF, to stop the extraction then the Timer and after 2 sec. the OFF button. The downdraft will carry out the calibration of its aspiration panel rising and retracting for some centim- 18 eters. During this phase, the buttons on the pushbutton control panel blink. At the end of the calibration, the aspiration panel get back to the previous position and the button end to blink. Wait until the aspiration panel stops moving before r

Downloads : 8   Arquivo Tamanho: 10 mb   Fabricante : Hunter Fan  
Categoria : Fans
@name@name@name

Turn on the power source. D23 Go to step on page 18 to attach grille. E1 E1 E2 L K Remove the thumbscrews. Connect wiring harness. E4 E3 J K Remove the strain relief bracket screw. Position the strain relief bracket under the motor as shown. E6 E5 Align posts A, B, C and D (stamped into motor housing) with posts A, B, C and D (stamped into light fixture). Slide light fixture over posts. Insert the strain relief bracket’s dog-leg tab so that it hooks over the lip of the motor. Reinstall the strai





categorias