Log:
Downloads : 1   Arquivo Tamanho: 72 kb   Fabricante : York  
Categoria : Fans
@name

or downloaded @ When ordering thru Baltimore Parts Center (BPC), part number's with less than eight digits may require a "NAC" prefix to the part number. Example: Motor part number in this manual is 432-3429; order thru BPC may need the prefix NAC432-3429. 2 YORK INTERNATIONAL FORM 115.23-RP1 (1104) DETERMINATION OF RIGHT-HAND / LEFT-HAND REFERENCES HORIZONTAL UNITS VERTICAL UNITS RIGHT END COMPARTMENT PARTS LIST ACTUATORS Part # Description Where Used 130-0041 Actuator, roll dampe

Downloads : 5   Arquivo Tamanho: 72 kb   Fabricante : York  
Categoria : Fans
@name

Box 1592, York, Pennsylvania USA 17405-1592 Copyright © by York International Corporation 2004 Form 115.23-RP1 (1104) New Release Tele. 800-861-1001 Subject to change without notice. Printed in USA ALL RIGHTS RESERVED

Downloads : 0   Arquivo Tamanho: 72 kb   Fabricante : York  
Categoria : Fans
@name

ÜYORK’ UNIT VENTILATORS RENEWAL PARTS New Release 115.23-RP1 (1104) MODELS: YH0W, YH0S, YHXS, YHXW, YHCS, YH0A, YHB0, YHA0, YHCW, YHAB, YH0B, YHXE MODELS: YTOW, YTOA, YTOS, YTOB, YTOE, YTBO, YTCW, YTA0, YTCS, YTAB, YTBE, YTXE,YTXW, YTXS, YTXB, YTXO FORM 115.23-RP1 (1104) TABLE OF CONTENTS DETERMINATION OF RIGHT-HAND / LEFT-HAND REFERENCES.............3 ACTUATORS...................................................................................................4 MOTORS..................

Downloads : 22   Arquivo Tamanho: 72 kb   Fabricante : York  
Categoria : Fans
@name

or downloaded @ When ordering thru Baltimore Parts Center (BPC), part number's with less than eight digits may require a "NAC" prefix to the part number. Example: Motor part number in this manual is 432-3429; order thru BPC may need the prefix NAC432-3429. 2 YORK INTERNATIONAL FORM 115.23-RP1 (1104) DETERMINATION OF RIGHT-HAND / LEFT-HAND REFERENCES HORIZONTAL UNITS VERTICAL UNITS RIGHT END COMPARTMENT PARTS LIST ACTUATORS Part # Description Where Used 130-0041 Actuator, roll dampe

Downloads : 1   Arquivo Tamanho: 1 mb   Fabricante : Trane  
Categoria : Fans
@name

The basic unit does not have filters in it. However, a filter frame accessory is offered that will allow filters to be installed within the unit. Otherwise a filter rack must be installed by the installer in the duct work. Affix the filter label supplied with the unit adjacent to the filter area. TABLE 4 UNIT NOMINAL CFM FILTER* Sq.Ft.- SIZE FILTER RESISTANCE YCZ036F 1200 4 0.05 YCZ050F 1600 5.33 0.05 YCZ060F 2000 6.67 0.05 *Filters must be installed in the return air system. The above square fo

Downloads : 6   Arquivo Tamanho: 1 mb   Fabricante : Trane  
Categoria : Fans
@name

Please return to service information pack upon completion of work. HAZARDOUS VOLTAGE - DISCONNECT POWER BEFORE SERVICINGWARNING: All phases of this installation must comply with the NATIONAL, STATE & LOCAL CODES. In the absence of local codes, the installation must conform with National Electric Code -- ANSI/NFPA 70 or "LATEST REVISION." Since Trane has a policy of continuous product and product data improvement, it reserves the right to change design and specification without notice. © 2002 Ame

Downloads : 0   Arquivo Tamanho: 1 mb   Fabricante : Honeywell  
Categoria : Fans
@name

Remote switch is on • Adjust remote switch to desired position. Thermostat Fan switch is in On position • Normal operation. HVAC system is running to satisfy heating or cooling requirements. • Normal operation. Ventilation limit is set to 100% ventilation limit. • Set ventilation limit to 60%. The control may not be able to meet the recommended ventilation requirements. • Increase ventilation airflow through fresh air duct and adjust settings. Low ventilation air flow. • See Problem: Not enough

Downloads : 1   Arquivo Tamanho: 1 mb   Fabricante : Hunter Fan  
Categoria : Fans
@name

BEDROOMS M22009 Ventilation Limit* Ventilation Standard 1 2 60% ASHRAE 62.2 100% 62-1999 Setting ventilation limit and ventilation standard. 68-0282—07 6 Y8150 FRESH AIR VENTILATION SYSTEM, W8150 FRESH AIR VENTILATION CONTROL Y8150 FRESH AIR VENTILATION SYSTEM, W8150 FRESH AIR VENTILATION CONTROL 1. Be sure power is turned on. 2. Set the Ventilation Standard on the control. 3. Set the bedrooms dial. 4. Set the area (sq ft) dial. 5. Set the airflow (cfm) dial. 6. Press the test button and observe

Downloads : 1   Arquivo Tamanho: 814 kb   Fabricante : Applied Energy Products  
Categoria : Fans
@name

6. Go outside and cut a hole in the outer wall, repeating the process described above. 7. Cut ducting to the correct length if required. 8. Fit the ducting. Ensure that the duct slopes down away from the fan to allow drainage of any incoming rain water to the outside. 9. Make good the hole around the ducting. Allow the mortar to set before continuing with the fan installation. If installing in a window or panel 1. Cut a hole, 125mm in diameter or if installing in a window, obtain a ready cut pan

Downloads : 6   Arquivo Tamanho: 814 kb   Fabricante : Applied Energy Products  
Categoria : Fans
@name

Before cleaning, isolate the fan completely from the mains supply. 2. Remove the front cover by pressing the release catches located on the sides of the unit with a 3mm screwdriver, whilst pulling the front cover forward (fig. E). 3. To clean the front cover, either wipe it with a damp, lint free cloth or wash it in warm soapy water. Thoroughly dry the front cover and refit. 4. Do not immerse the fan in water or other liquids to clean any other parts of the fan. 5. Do not use strong detergents,





categorias